Treating a pool requires balancing acidity and alkalinity and sustaining a pH of between 7.2 and 7.8. Along with chlorine, baking soda is an important part of your pool maintenance routine. There are many reasons to use baking soda in your pool to keep your water clean, clear, and safe for swimmers.
I have a question, i'm doing the shock on my pool now. Could i add (stabilizer, baking soda, borax, or etc) to my pool while doing the shock time? Or i have to wait until the shock is done. Stabilizer, yes, if you're below 30 CYA.
Incompatible Pool Chemicals
Mixing of organic chlorinating agents (such as trichloroisocyanuric acid) and inorganic chlorinating agents (such as sodium hypochlorite) can lead to fires, explosions and chlorine gas release.
The Orderly Addition of Chemicals
If both the pH and total alkalinity levels are too high, you'll need to add pH reducer. Once you get your pH levels between 7.2 and 7.5 and your total alkalinity between 60 and 120 ppm you can move on to working on the calcium hardness and chlorine levels.
Alkalinity is the total alkaline material in your pool water. You should test alkalinity first because it will buffer pH. Your reading should be in the range of 80 to 120 parts per million (ppm).
Undissolved Granules
The presence of these granules does not indicate that you have added too much stabilizer -- the product is slow to dissolve, particularly when static. You can speed the process by agitating the granules with a brush so that they circulate in the pool water.
Despite being chlorinating agents, they are incompatible. Do not add at the same time or mix muriatic acid and chlorine. Such interaction produces a toxic gas that is dangerous to health even in small amounts. A good rule of thumb is to never mix pool chemicals with each other.
It is recommended to wait at least 20 minutes to an hour after adding water balancing chemicals. You should wait 2-4 hours (or one full cycle through the filter) to swim from the moment you use calcium chloride in your pool. It is safe to swim once your chlorine levels are around 5 ppm or after 24 hours.
Using baking soda will not actually lower your pool's chlorine level. If your ph is way too low it may. Prevent corrosion and damage to pool equipment; To raise your ph levels, it can be as simple as adding seven to nine pounds of baking soda to your pool water.
It Should Not Be Done Together
This is because when you mix chlorine and algaecide together, it renders both of them useless. Hence, you should first shock the pool and wait for the chlorine levels to fall below 5 PPM. Only then should you introduce algaecide to get the best results.
Before getting in
Don't swim or let others swim if sick with diarrhea. Shower for at least 1 minute before you get into the water to remove dirt or anything else on your body.
Chlorine issues often cause cloudy water. Adding a recommended dose of pool shock to your pool can clear it right up. Poor circulation or filtration can contribute to cloudy water. Make sure your pump and filter are working properly.
The most important factor though is the size of the pool. You'll need about 52-104 oz of liquid chlorine per 10,000 gallons of water. This amount should get the chlorine level to between 5 and 10 ppm.
High chlorine levels decrease the pH of your pool's water, making it more acidic. The more acidic the water, the higher the likelihood of corrosion.
To bring down pH, use a made-for-pools chemical additive called pH reducer (or pH minus). The main active ingredients in pH reducers are either muriatic acid or sodium bisulfate (also called dry acid). Reducers are readily available at pool supply stores, home improvement centers and online.
If the tablets are not dissolving, and you get a strong smell of chlorine when you open the chlorinator, you probably have a bad check valve in the chlorinator. It is not allowing any water to move through the chlorinator, and any water that is there simply sits there and builds up a yellowish chlorine gas.
There are two methods you can use to dissolve stabilizer into your pool water. You can either add the stabilizer to a pool skimmer box sock and hang the sock in front of the return jet or place it in the skimmer box. Or you can simply mix it in a bucket of water first and dump it into the skimmer box.
Other causes of low alkalinity include: overuse of alkalinity lowering products (i.e. muriatic acid) using too many chlorine tablets with low pH. excessive rainwater diluting the pool.
Before shocking the pool, be sure that you have properly balanced the Total Alkalinity, pH, and Calcium Hardness levels, and have addressed metals in the pool.
Here are common causes of an alkaline pool: Algae can raise the pH. Adding strong liquid chlorine, calcium or lithium hypochlorite chlorine may raise it. Suddenly heating the water, whether from a pool heater or a string of sunny days, could up the pH.
Strong Smell of Chlorine
A healthy, safe pool will have little to no odor. That smell comes when your pool is out of balance. The smell of chlorine arises when the chemicals are dealing with a lot organic material like sweat, urine, and bacteria in your pool.
In most cases, the walls and floor of your pool feel slimy and slippery due to a lack of pool maintenance. Water chemistry is important in order to maintain clear and bacteria-free water. Generally, slippery and slimy pool walls are an early indication of bacteria and algae growth.