A cracked or burned-out furnace ignitor cannot be safely or effectively repaired; it must be completely replaced. However, if your furnace is simply struggling to fire up, a technician may be able to clean a dirty flame sensor (which can look like an ignitor) or safely adjust a misaligned pilot assembly.
Parts: A new hot surface ignitor typically costs between $30 and $60. Labor: Professional labor costs usually range from $120 to $240, depending on your location and the service provider. Total Average Cost: Most homeowners can expect the total furnace ignitor replacement cost to be between $150 and $300.
A furnace ignitor typically lasts between 3 to 7 years, though exact lifespan depends on its material.
To determine if your furnace ignitor is bad, look for visible cracks, listen for repeated clicking noises without a flame, or check for a bright orange glow during startup. To confirm a failure, you can test it using a multimeter set to measure resistance (Ohms).
So, when you have a faulty furnace ignitor that is not working correctly, the furnace won't be able to ignite, and the heating system comes to a stop as it won't be able to generate and blow hot air.
Resetting a furnace igniter usually involves performing a power cycle to clear a system lockout, though some electric models have a physical high-limit reset button. If the igniter is cracked or covered in carbon buildup, it will need to be inspected and potentially cleaned or replaced.
The heat exchanger is often considered the most costly part of a furnace to repair or replace. It is a critical component that transfers heat from the combustion process to the air that circulates throughout your home. Over time, heat exchangers can crack due to the constant heating and cooling cycles they undergo.
To get your furnace to kick on, first verify your thermostat is set to "Heat" and raised at least 5 degrees above room temperature. Next, check that the furnace power switch (usually resembling a standard light switch on or near the unit) is toggled "ON".
The $5,000 rule is a guideline to help homeowners decide whether to repair or replace their HVAC system. You multiply the age of your unit by the cost of the needed repair. If that number exceeds $5,000, replacing your HVAC system is often more cost-effective.
You should probably Replace if: [ ] The repair costs more than 50% of a new unit. [ ] The furnace is over 15 years old. [ ] You have had to repair it more than once in the last 2 years.
A dirty furnace flame sensor is one of the most common ignition issues, and one of the easiest to fix when caught early. Become a Kauffman Gas customer and let our team inspect, clean, and restore your ignition system before a minor buildup turns into a full breakdown.
Replacing a furnace ignitor typically takes 15 to 45 minutes. An experienced technician can often complete the job in under 20 minutes. The process involves shutting off the power, removing the access panel, swapping out the part, and reassembling the unit.
The igniter glows red and then lights the burners in the gas furnace. Over time, the igniter is continually getting red hot and then cooling, creating stress on the element. Because of this, igniters have a 3-5 year life expectancy. They will eventually crack and need to be replaced.
The average cost to replace a furnace ignitor is $300–$425, including parts and labor from a professional. A home warranty is likely more expensive than the cost to just replace a furnace ignitor directly.
Turn off power and gas to your furnace at the breaker and gas valve. Remove the access panel and locate the ignitor near the burner assembly. Disconnect wires and unscrew the mounting bracket holding the old ignitor. Install the new ignitor carefully (wear gloves to avoid skin oils damaging it)
5 Warning Signs It's Time for Furnace Replacement
However, with the passage of the new budget, homeowners now have until the end of 2025 to take advantage of the HVAC tax credits, which include: $2,000 for a qualified heat pump. $600 for a qualified air conditioner. $600 for a qualified gas furnace.
A standard furnace lasts between 15 and 20 years on average, though electric furnaces can stretch up to 20 to 30 years. Regular maintenance, such as annual tune-ups and changing your filters every 1 to 3 months, is the most important factor in reaching or exceeding this lifespan.
When your furnace clicks but refuses to turn on, it typically means the electronic ignition sequence has failed. This is often caused by a dirty flame sensor, a cracked or burnt-out igniter, or a faulty gas valve.
Although comfort is personal and can vary, a generally comfortable temperature for a house is often set between 68 and 72 degrees Fahrenheit. This range is considered ideal for most people to feel comfortable indoors.
Your furnace’s reset button is typically a small, bright red or yellow button located either inside the blower compartment, near the burner assembly, or directly on the motor housing.
What fails first on a furnace? The most common early failures are the furnace ignitor or flame sensor, as they experience regular wear and tear and are critical to starting the heating cycle.
Try the Salvation Army, a local church, or a community action agency. Their rules may be different. Ask About Payment Plans: Many local HVAC contractors, including Smart Climate Solutions, offer payment plans for urgent repairs because we believe everyone deserves a warm home.
Yes, you should highly consider replacing a 30-year-old furnace. Most furnaces have a lifespan of 15 to 20 years. At 30 years old, your system has likely outlived its expected life. It is operating at a much lower efficiency than modern units and presents a significantly increased risk of catastrophic breakdown or dangerous carbon monoxide leaks.